Wednesday, May 13, 2009

Go with the Flow

I am pretty sure that my Exposed print is of sufficient value to cover the "cost of entry" to the Oceans of Art exhibition at the Nanaimo Art Gallery, opening reception on Thursday June 11, 7-9 pm; however, I also thought that a few smaller pieces may be appreciated, as it can sometimes be difficult to sell large pieces.

I had done a sketch of a piece of kelp (Macrocystis) that I'd photographed on Brady's Beach that I've had sitting in the back of my mind since I did it, with the intention of a reduction cut.

I started off with a yellow ochre layer (didn't photo it), then later did a separate set of prints with a blend (rainbow) roll using yellow ochre, carbazole violet, and phthalo green:

Amie Roman as burnishings on Flickr

Flow II
MDF block print, Dremel carved
Daniel Smith water soluble inks on green kitakata paper
© Amie Roman

and then for some reason, printed the remaining ink on the block (not reinking the block) over the ochre layer and got this:

Amie Roman as burnishings on Flickr
Flow I
MDF block print, Dremel carved
Daniel Smith water soluble inks on green kitakata paper
© Amie Roman

After I finished enough prints for editions for those two, I decided to mess around a little and ended up with these two monoprints:

Amie Roman as burnishings on Flickr
Flow VI
MDF block monoprint, Dremel carved
Daniel Smith water soluble inks on white Rising Stonehenge paper
© Amie Roman

Amie Roman as burnishings on Flickr
Flow VII
MDF block monoprint, Dremel carved
Daniel Smith water soluble inks on white Rising Stonehenge paper
© Amie Roman

Then I got to the part that I'd really intended all along! I carved another layer for the reduction (only one; I wanted to keep it very simple). I printed over some of the Flow I prints (but kept some set aside for their own small edition):

Amie Roman as burnishings on Flickr
Flow III
MDF block reduction print, Dremel carved
Daniel Smith water soluble inks on green kitakata paper
© Amie Roman

And then, of course, had to print over some of Flow II, too (also setting aside some of them with only the first blend roll for their own small edition):

Amie Roman as burnishings on Flickr
Flow IV
MDF block reduction print, Dremel carved
Daniel Smith water soluble inks on green kitakata paper
© Amie Roman

This second, carved layer was also a blend roll, but subtle to see, except for in the edition I did on its own:

Amie Roman as burnishings on Flickr
Flow VII
MDF block print, Dremel carved
Daniel Smith water soluble inks on white Rising Stonehenge paper
© Amie Roman

There are so many things about this series that I'm absolutely tickled by:
  1. The simplicity of the carving is exactly what I had wanted to achieve, and very effectively reflects the gorgeous lines and shapes of the Macrocystis frond that I'd sketched.
  2. The success of the rainbow roll in capturing the oil-slick colours of a slightly decaying, washed up piece of kelp on the beach.
  3. The subtleties in value contrasts between II and III which again, really captures the ever-changing colour shifts of a washed up piece of kelp on the beach.
  4. I got to do a series!! And I played a lot, both with the colour and the printing.
Plus, my baby press is an utter jewel. Love it!

Oh, yeah, and I'd just invested in a set of Foredom ceramic rotary tips for my Dremel tool, and they are absolutely fabulous for carving the MDF in the way I want to.

As you can see, I had a very productive couple of days last week. I won't be donating each of these, but I'll pick a couple to frame up and add to the show.

Now I'm going to be away from the studio for at least another week or so, but hope to get back to it when I return, as I've got lots of ideas that I'd really like to work on.

6 comments:

Sherrie York said...

Beautiful! I can never decide if I'm inspired or chastened by such wonderful and successful experimentation. You go, girl!

(Oh, funny... it's not spelled correctly, but the word verification is "layar". Sort of a prinntmaker's word, eh?)

Unknown said...

Says such a talented printmaker herself... I'm constantly inspired and guilt-ridden by Sherrie's incredible work.

Dean Russell Thompson said...

Nice work! I agree that the relatively simple lines combined with the graded roll is quite effective.

I have not tried using stones to work MDF, my weapon of choice is a solid carbide burr.

Ellen Shipley said...

I love Flow IV. Beautiful. 8-]

Ellen Shipley said...

I mean Flow VI -- always get my Roman numerals mixed up. ;-j

Michelle Turbide, an artist on a soul journey said...

I love the experimenting that you did with this. I love the colors and composition! great work Amie.